• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Glass Window Repair

Professional window repairmen are able to move large panes of tempered glass from a height higher than the ground. They adhere to strict safety standards and are often working in extreme weather conditions.

Wearing protective clothing, remove all glazing putty and metal glazing points using a utility knife. A heat gun may help soften the old glue and speed up removal.

Replacement

When a window pane breaks, it could be tempting to repair the glass rather than replace it. It is cheaper to replace a window, and it can also help you avoid other issues that could affect the efficiency of your home. Consider the kind of glass damaged to determine whether it's a temporary fix, or if a permanent solution is required.

The first step in repairing broken windows is to take off the sash, also known as the frame and lay it flat on a table. Wearing eye protection, gently move the frame and remove any remaining shards in the window. Utilize a utility knife to remove the glazing compound and the glazing points that keep the window in place. Keep the track of the components and their location to ensure they are reinstalled.

After removing the frame and sash, you can begin preparing to replace the glass. Before you do so make sure that the opening in the frame is designed for the replacement window. Measure both ways across the opening, and then subtract 1/8 inch from each measurement to allow space for expansion and contraction of the frame and glass. Then, purchase double-strength glass cut to these exact dimensions. It is also recommended to purchase enough new glazier's glazier's pointing or clips to be installed every 6 inches around the window pane.

If the manufacturer is accountable you should contact them and submit a claim. After the new glass has been erected it is crucial to cover it with a thin layer glaziers compound. Once the compound is dry, you can paint the frame to be a perfect match.

If you have a crack that extends more than an inch, scoring the crack with a razor blade that is just above the crack will help prevent it from spreading any further. This technique isn't 100% foolproof, but it can slow the development of the crack down to a manageable amount until you can take permanent measures.

Repair

Professional window installers have the right tools and know how to handle different kinds of glass. They know how to dispose of waste properly, so they are less likely than others to leave behind scraps that could harm family pets or family members. They're also accustomed to working with different types of windows, and may be able to spot problems that a home owner with no experience would not notice.

Wear safety goggles and gloves before you begin the process of repairing cracked glass. Even a small break can cause shards to fly off, which could pose a risk to anyone living in or around the home. It is crucial to determine the cause of the crack, as this could prevent future problems.

Start by making a two-part epoxy mixture. These are usually a 50/50 mix of hardener and resin, and they must be mixed quickly. After the mixture is prepared, apply it directly to the crack and allow it to dry. It will take just about a minute however it is important to get it done quickly as the mixture is very thick and fast-drying.

Once the epoxy has dried, you can take off excess epoxy with a blade. Then, you'll have to clean the area around the broken glass. If you don't clean the area correctly the debris could cause further damage to the glass. Make use of a putty knife to smooth out the compound around the edge of your window and then match it to the frame made of wood.

To make a more durable option you can consider using a plastic covering. You can cover the glass using masking tape or a sturdy trash bag. This will prevent the crack from spreading, and will also keep water, wind and insects out.

You can make an interim fix in the event that you are unable to access the window in an efficient manner. Apply a small amount silicone sealant to the edges of the broken glass. It won't close the gap between the frame and the glass completely, but it will hold the break in place until you are able to repair it.

Repainting

Repainting your old glass windows is a good idea. This is a cost-effective alternative to window replacement and will give your home a fresh new appearance. Before painting, make sure the surface is clean. Use soap or rubbing alcohol and water repairs to double glazed windows wash away oil smudges, as well as other residues which can prevent paint from adhering. Wear rubber gloves when working on glass surfaces to prevent the transfer of oils from your hands onto the glass. Apply multiple thin coats instead of a single thick one. This will help the paint last longer, and ensure that your windows appear smooth and even.

Make sure you have the proper tools available if you plan to repaint glass windows. You'll need a brush, sponge, painter's tape, toothpicks, a ruler as well as a few other tools such as paper towels or a rag. It is recommended to have the brushes and paints you will be using on hand. Follow the instructions of the manufacturer. Be patient, as it may take a while for the paint to fully dry.

Also, ensure that the space you're working is well ventilated if you're using solvent-based paint. This will reduce the chance of breathing in toxic chemicals and allow the paint to dry faster. Also, make sure you have a protective mask for any spray paints you apply.

For older glass windows, you'll need to prepare the surface before painting. Clean the glass thoroughly with soap and warm water. You can then apply rubbing alcohol to wash off any oil or grease that might hinder the adhesion of the paint. Make sure the windows are dry before you start coating them.

If your glass windows are energy efficient dual pane windows, you may be able to make a claim with the window manufacturer or dealer that sold them to pay any repair or replacement costs. This is especially true if your windows are still under warranty and you've had numerous issues with condensation or broken glass.

Sealing

There are a variety of options to fix the problem depending on whether you have an old double glazing repair-pane glass with cracks in the seal or if you have an upgraded insulated unit (IGU) that has experienced defogging. It is the most expensive option to replace both the insulation unit and the frame. However, it could be necessary in cases where fog or condensation is creating energy loss. Other options include replacing the existing IGU with a single pane or repair double glazed window it by drilling a small hole through the bottom of the unit, and then filling the solution with anti-fog.

You can also close the gap between a window frame and a threshold or sill with a felt strip or vinyl V-strip. Felt can be stapled, glued, or placed in place, but is not a great protection against moisture. Vinyl v-strip is easy to put up and is durable however it can be expensive. It is typically reserved for areas that are exposed to abrasions that are high. Door sweeps are able to be easily nailed to the floor and are affordable. However, they offer little or no protection between the threshold and air.

To repair a damaged Window Repairing seal first, use a putty knife to scrape off the caulk. Wearing gloves and eye protection, carefully pry out the glazing points -- tiny fasteners that pin the glass to the frame's recess with sharp edges and pointed ends. After you have removed the glazing points, clean the grooves and sand the wood to a smooth finish. Wipe off any sanding traces and then seal the unfinished wood using a linseed oil-based paint or clear wood sealer.

A caulking knife or putty can be used to apply the traditional glazing putty, however using a knife will give the most precise application and a stronger seal. Choose a putty specifically for glass as it will be more durable and stick better.

Apply a thin layer of putty on the inside of the frame where it joins the glass. Slide the window into the frame so that the scribed line on the glass lines up with the edge of the frame. Apply pressure on the glass to compress the putty and create an elongated seal. Smooth the compound using an ungloved finger, and wipe away any caulk that is applied incorrectly or errant drips before it is dry.