• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Most homeowners can fix hinges that are loose. If the holes for screws are shattered and do not hold screws, you might require wood glue and dowels to put back in the broken window hinge repair.

Remove any surface corrosion. This will help to keep the dowels in their place and provide a solid foundation for them to grip onto.

Take off the Hinges

A variety of door hinges can be removed, which makes it easier to move doors from one side of the frame to the other or take the entire door off when needed. It is easy for anyone with patience, although you need to know how to do it properly.

If the hinges are painted you'll need to take off the paint prior to trying to remove the pins. You may scratch your door if you don't take off the paint. To break the seal put the hinges in an stainless steel pan and fill the pan with water until the hinges are fully submerged. Let the hinges rest in the pan for 30 minutes. The heat from the water will soften the paint and make it easier to get rid of the pins.

After the pins have been loose, remove the awning window hinges and the frame from the door. You can make use of a screwdriver to get the job done, however it is recommended that you employ a magnetic screwdriver to complete this task. This type of screwdriver was designed to pick up screws made of metal and can make the work speed up.

Before you attempt to remove the hinges it is a good idea to spray them with grease. A simple lubricant will help you to accelerate the process and make the removal of screws and pins easier. This type of lubricant can be found in most hardware stores and home improvement stores.

Keep in mind that the number of door hinges you'll need will vary depending on the door's type and its configurations. Heavier doors and solid-core doors will require more hinges while hollow-core doors that weigh less might require just two or three hinges.

It is also important to be aware of the various kinds of hinges to determine which ones will work best in your situation. Exterior hinges are designed to support the weight of a door, but interior hinges must be able to support heavier loads.

Reattaching the Hinges

Over time the hinges on doors can become loose and start to hang crooked or sag. It can be a big problem, but the fix is usually easy. Most of the time, a simple retightening of the screw will resolve the issue. However when the screw holes have been stripped out, this may be more difficult to do. A dowel made of wood can be used to tighten the holes once more.

Start by drilling out the old hole using a drill bit that is close to the size of the new screw (typically 3/8"). Then, you can use wood glue and a wooden dowel to fill the hole. The dowel should be cut to a length that is exactly the same as the screw to ensure a secure fit. Then, you can reinstall the screw and tighten it to the desired level of tightness. If the door does not stop bind up, insert a second dowel into the gap. Repeat the process. Make sure to close the door slowly in order to verify the clearances at the perimeter after each adjustment.

You can also use a wooden plug in place of the dowel. It will work similarly, but it may take a little longer to set up. You can insert a piece of wood that has been whittled down to the proper size. If you don't have a woodworking tool you could also try using toothpicks or wooden matches.

Once you have reinstalled the new screw and countersink the screw, you can use a countersink tool to make the hole for the screw's head smaller so that it won't touch the edge of the door when it is opened and closed. This will make it easier to tighten the screws before reinstalling hinges.

After installing the hinge, lubricate the hinge with dry lubricant. This will help to prevent it from getting stuck in the future. Products such as PB Blaster or Liquid Wrench are good options. You should apply a light coat and allow it to take about 15 minutes to fully get into the barrel of the hinge.

Refinishing the Hinges

If you're not ready to replace hinges, you could try a few fixes. Verify that the screws that secure the hinge plate to the door frame as well as the frame are in good condition. If they're loose, tighten them using the help of a screwdriver or a power drill. Be cautious not to over tighten the screws, because this can cause gaps to form at the trim joints or worse, strip out the threads.

If the problem is the hinge plates are breaking, you can reattach the plates by applying wood glue on the back of them and then inserting wooden dowels or toothpicks into the holes. Dowels and toothpicks create a solid foundation for the screws, which will stop the plates from moving as you drive them in. Let the glue dry before attaching the hinge.

The screws could also be stripped or missing. This can be fixed by replacing the screws with larger ones. Use a drill bit that is the same size as the screw hole to prevent drilling into the jamb or hinge.

Close the door once you've reattached the hinge and examine the gap between the frame and the door. The gap should be the thickness of a penny or less if the old door was not properly hung. This shouldn't be a problem as long as the hinges are properly installed.

If you find that the hinges are loose, try putting an extra thicker shim between the hinge plate and the mounting surface to add an extra inch of space. You can also remove the hinge pin and pound it down with a powerful hammer to tighten it or use the hinge of a different type. It is also possible to lubricate the hinges with mineral or Jojoba oil to lessen friction and aid in holding their place. Lubricating your hinges frequently will keep them from becoming stiff and squeaky and also extend their lifespan.

Cleaning the Hinges

The constant movement of a hinge creates friction, which draws dust particles. These particles can become stuck and accumulate in the moving parts of door repair window hinges if they are not cleaned and lubricated regularly. The hinge will become stiff and creaky and its appearance may rapidly deteriorate. Regular cleaning, lubrication, and inspections can maintain the quality of a hinge on a door and ensure its proper function.

Check the hinges to see how to fix window hinges much rust has formed on their surface. If the rust is so bad that it has damaged the surface of the screw holes or the barrel of the hinge, you'll need to replace them. If you can save the hinges, you can remove any loose rust using wire brush and steel wool. Apply a commercial rust removal solution or homemade solutions like lemon juice on the hinge. Let the rust remover be on the hinge for a few minutes to dissolve and penetrate any remaining corrosion.

If you don't wish to spend cost and time to replace window hinges your hinges, simply retightening the screws will bring back the hinge's functionality. It might be necessary to add an shim of wood or a dowel to the hinge if the screw holes have been stripped. Wooden dowels come in round rods of varying sizes and lengths. They are available at home improvement centers, woodworking supply and craft shops, or on the internet.

A shim can be made of a piece of plastic or metal, based on the kind of hinge you have. To make a dowel, you need to cut a dowel from wood to the desired length. You can then dip the dowel in a glue for carpenters and then insert it into the cut hole and let the glue hold the dowel in the desired position.

Before cleaning the hinges put down a piece of paper towel or cloth to protect your flooring from spills. After the area is secured then clean the hinges with a soft sponge or cloth that has been soaked in mild cleaner or vinegar to get rid of built-up dirt, grime and tarnish. You can make use of a toothbrush or a small brush to get into difficult-to-reach areas in crevices and tight areas.